Faculty - TAKEUCHI Yoshimi |

TAKEUCHI Yoshimi

Department / Course Chubu University Educational Corporation

Chubu University

Job Chairman

Academic conference presentation
2019/06	Automated Workpiece Setting Operation and its Error Compensation on an Ultraprecision machine Tool (Proc. of 19th EUSPEN Int. Conf. USB 386-387)
2018/11	Deep Hole Machining with High Dimension Accuracy by Small Diameter Tools, Kamakura (Proc. of 17th ICPE, A-4-8, USB.1-4)
2018/11	Development of a Postprocessing System of Resin Organ Models by Utilizing 3-Axis CNC Abrasive Machining (Proc. of 17th ICPE, B-2-7, USB.1-4)
2018/11	Fabrication of Strength-Enhanced Eccentric Shaped Ball Eng-Mill (Proc. of 17th ICPE, A-4-7, USB.1-6)
2018/07	Development of CAM System for Variable Pitch Screw Fbrication (Proc. of Int. Symp. on Precision Eng. and Sustainable Manufacturing (PRESM2018), USB.1-5)
2018/07	Three-dimensional Micro Shape Creation on a Workpiece Located by Industrial Robot (Proc. of Int. Symp. on Precision Eng. and Sustainable Manufacturing (PRESM2018), USB.1-3)
2018/05	Three-dimensional Micro Shape Creation by On-machine Scanning Measurement (Proc. of 18th EUSPEN Int. Conf., USB.135-136)
2017/11	Automated Finishing of Organ Models Created by 3D printing (Proc. of 9th International Conference on Leading Edge Manufacturing in 21st Century (LEM21), CD-ROM 1-5)
2017/11	Creation of New Eccentric shaped Ball End-Mill without Separation Line (Proc. of 9th International Conference on Leading Edge Manufacturing in 21st Century (LEM21), CD-ROM 1-5)
2017/11	Hole Fabrication inside a Hole by Means of Electrical Discharge Machining -Expansion of Machinable Hole Diameter- (Proc. of 9th International Conference on Leading Edge Manufacturing in 21st Century (LEM21),CD-ROM 1-5)
2017/09	Automated teaching Process in Teaching Playback method for Curved Hole Electrical Discharge Machining (Int. Conf. on Design and Concurrent Eng. 2017 & Manufacturing Systems Conf. 2017, JSME,Short paper No.25, 1-5)
2017/08	A Study on Automatic Compensation of Workpiece Setting Errors in Ultraprecision Machining (Proc. of 7th ASPEN, USB.1-3)
2017/05	5-Axis Control Finishing for Decreased Tool Wear (Proc. of CIRP Conf. on Manufacturing Systems, Procedia CIRP 63 313-317)
2017/05	Dexterous Machining of Unstable Thin Plate (Proc. of CIRP Conf. on Manufacturing Systems, Procedia CIRP 63 324-329)
2017/05	Setting errors compensation of a workpiece located by industrial robots (Proc. of 17th EUSPEN Int. Conf.,USB.223-224)
2016	5-Axis Control Finishing Suppressing Tool Wear (Proc. of ICPE, B305, USB.1-4)
2016	Automatic Tool Setting Errors compensation in Ultraprecision Machining (Proc. of 16th EUSPEN Int. Conf., USB.483-484)
2015	6-axis Control Ultraprecision Machining Based on Compensation of Tool Setting Errors (Proc. of 15th EUSPEN Int. Conf. 297-298)
2014	5-axis Control Ultraprecision Machining Based on Tool Setting Errors Compensation ICMT (Proc. of 18th Int. Conf. on Mechatronics Technology (ICMT2014), USB 1-4)
2014	Fin Fabrication inside a Hole by Means of Electrical Discharge Machining and Reciprocating Block Slider Crank Mechanism -Improvement of Machining Device and Verification of Its Potential- (Proc. of ICPE, Poster 28 690-691)
2014	Reduction of Power Consumption in Rough Turning (Proc. of ICPE, D09 473-477)
2014	Tool Setting of Error Compensation for Multi-axis Control Ultra-precision Machining (Proc. of 14th EUSPEN Int. Conf., Vol.2, 43-46)
2013	5-Axis Control Ultraprecision Dexterous Micromachining of Möbius Ring (Proc. of 13th EUSPEN Int. Conf., Vol.2, 64-67)
2013	Application of ultraprecision microgrooves to dental implant and blood inspection (Proc. 1st CIRP Conf. on BioManufacturing, 147-151)
2013	Development of CAPP System for Multi-tasking Machining of Complex Shapes (Proc. of 6th International Conference on Leading Edge Manufacturing in 21st Century (LEM21), D018, SD-Card, 527-530)
2013	Fabrication of Spherical Microlens Array Mold by Ultra-precision Multiaxis-control Milling (Proc. of 13th EUSPEN Int. Conf., Vol.2, 101-104)
2013	Fundamental Study on Fabrication inside a Hole by Means of Electrical Discharge Machining (Proc. of 6th International Conference on Leading Edge Manufacturing in 21st Century (LEM21), C015, SD-Card, 373-376)
2013	Ultraprecision Cutting of SiC by Rotational Diamond Tool with Special Chamfer (Proc. of ASPEN, USB.1-4)
2012	Development of 5-axis Control CAM System for Multi-tasking Machine Tools (Proc. of 45st CIRP Conf. on Manufacturing Systems (CIRP-CMS2012), 266-270)
2012	Microgrooving with Flat-ends for Hard Materials (Proc. of 12th EUSPEN Int. Conf., Vol.2, 96-99)
2012	Microgrooving with Flat-ends for Hard Materials (Proc. of 12th EUSPEN Int. Conf., Vol.2, 96-99)
2012	Study on 2+1 Axis Control Electrical Discharge Machining of 3-dimensional Cross Section’s Changing Hole (Proc. of 16th Int. Conf. on Mechatronics Technology (ICMT2012), CD-ROM, 553-558)
2012	Ultraprecision Micromachining of Micro Lens on Roll Mold Die (Proc. of 16th Int. Conf. on Mechatronics Technology (ICMT2012), CD-ROM, 548-552)
2011	Creation of Microgroove with Two Flat-ends on Hard-Brittle Materials (Proc. of 6th Int. Conf. on MicroManufacturing (ICoMM), 615-619)
2011	Development of Conceptual Design Assistance System for Machine Tool Structure with Consideration of Feed Drive Mechanism (Proc. of 6th International Conference on Leading Edge Manufacturing in 21st Century (LEM21), No.3288, CD-ROM, 1-4)
2011	Dexterous Machining of Chain-Shapes by Employing a Multi-Tasking Machine Tool (Proc. of 15th Int. Conf. on Mechatronics Technology (ICMT2011),59-62)
2011	Efficient Tool Path Generation for Five-Axis Controlled Machining by Use of Square End Mill (Proc. of 6th International Conference on Leading Edge Manufacturing in 21st Century (LEM21), No.3282, CD-ROM, 1-4)
2011	Precision Complex machining of Glass Lens Mold with Fresnel Shape (Proc. of 11th EUSPEN Int. Conf., Vol.2, 505-508)
2011	Precision Machining of Non-axisymmetric Aspheric Glass Lens Mold with Micro Fresnel Structures (Proc. of ASPE Spring Torical Meeting, 24-28)
2011	Ultraprecision Low-wear Micro Curved Grooving of Hard Material (Proc. of 6th Int. Conf. on MicroManufacturing (ICoMM), 605-609)
2011	Ultraprecision Microgrooving on Hard Material with Tool Wear Suppression (Proc. of 26th ASPE Annual Meeting. CD-ROM 3293)
2010	5-Axis Control Ultraprecision Micromilling by Means of a Developed CAPP/CAM System (Proc. of 10th EUSPEN Int. Conf., Vol.2,65-6)
2010	CAM System Development for Multi-tasking Machine Tools (Proc. of 43th CIRP Conf. On Manufacturing Systems, 1044-1051)
2010	Comparison of Path Generation Method for Efficient 5-axis Control Drilling of a Large Number of Holes (Proc. of 4th CIRP Int. Conf. on High Performance Cutting (HPC), 133-138)
2010	Creation of Microgroove with Two Flat-ends for Hard Material (Proc. of 25th ASPE Annual Meeting, 447-450)
2010	Current State of Art and Review in Micro Mechanical Machining (Proc. of Int. Forum on Micro Manufacturing,299-305)
2010	Design Assistance for Machine Tool Structure in the Conceptual and Fundamental Stage (Proc. of Int. Symp. on Flexible Automation,CD-ROM (JPL2546) 1-6)
2010	Development of a Process Planning System for 3+2 Control Rough Milling (Proc. of Int. Symp. on Flexible Automation, CD-ROM (JPL2660) 1-6)
2010	Development of CAPP/CAM System for Ultraprecision Micromachining -Process Planning for High-Aspect-Ratio Structures- (Proc. of 14th Int. Conf. on Mechatronics Technology (ICMT2010), 195-199)
2010	Development of Five-axis Machining Center Adopting Table-on-Table Type －New Structure and Baic Characteristics - (Proc. of 14th Int. Conf. on Mechatronics Technology (ICMT2010), 17-23)
2010	Dexterous Machining for a Complicated Shape with Nested Structure (Proc. of 14th Int. Conf. on Mechatronics Technology (ICMT2010), 28-31)
2010	Dexterous machining of Complicated Shape Consisting of Bended Columns (Proc. of 14th Int. Conf. on Mechatronics Technology (ICMT2010), 24-27)
2010	Highly Accurate 5-Axis Control Ultraprecision Micromachining by Tool Setting Error Compensation (Proc. of 2nd Int. Conf. on Process Machine Interactions (PMI), CD-ROM 1-8)
2010	Highly Efficient Cutting of Aspherical Surface of Cemented Carbide by Roational Diamond Tool with New Chamfer (Proc. of 14th Int. Conf. on Mechatronics Technology (ICMT2010), 221-225)
2010	Multi-Axis Control Ultraprecision Micromilling (Key Engineering Materials, Vol. 447-448 , 801-805, Proc. of ICoPE/ICPE2010)
2010	Rapid Tool Path Generation for 5-Axis Control Machining of Complicated Surfaces (Pro. of 2nd Int. Conf. on Process Machine Interactions (PMI), CD-ROM 1-9)
2010	Structure Design of Machine Tool in Consideration with Joint Damping at the Conceptual and Fundamental Stage (Proc. of 14th Int. Conf. on Mechatronics Technology (ICMT2010), 253-257)
2010	Tool Path Generation for 5-Axis Control Machining by Considering Tool Attitude and Attitude Variation (Proc. of 4th CIRP Int. Conf. on High Performance Cutting (HPC), 139-144)
2010	Ultraprecsion Microgrooving of Hard Meterial by Means of Cutting Point Swivel Machining (Key Engineering Materials, Vol. 447-448 ,36-40, Proc. of ICoPE/ICPE2010)
2010	Verification of Basic Performance of Size-Reduced Automatic Discharge Gap Controller for Curved Hole Electrical Discharge Machining (Proc. of 16th Int. Symp. on Electromachining, 127-132)